UPVC Window Handle Replacement

It is easy to replace a broken window handle with the right tools. It is important to identify the handle's type and spindle's length prior to purchasing the replacement.

Older uPVC windows feature handles with cockspurs, which have a spur that protrudes to the lock of a wedge cockspur striker plate. They can be right-handed or left-handed, and must be compatible when replaced.

What type of lock or handle do you have? I have?

There are many kinds of upvc window handles and locks, each with their distinct advantages and functions. The kind of handle you choose will determine how easy it is to open your windows glass replacement and whether or not the locking mechanism functions according to the plan. As time passes, and with regular use, the upvc handles on your windows could be damaged and worn out. This makes them less secure and less effective. In some cases they may even fall completely off. It is crucial to fix the handles on your window made of upvc when you notice they are falling off. This will help prevent potential break-ins and ensure your home is secure.

It is a good thing that replacing your window handles made of plastic is a fairly simple job that can be completed by everyone. You will need a few basic tools, but with right knowledge, it is an easy task that will only take a few minutes. You will need to know the type of handle or lock that you have on your window. This will help you choose the correct replacement.

Inline Espagnolette Handles

They are typically found on the side of the window. They are flat and have a latch which engages the locking mechanism of the window frame. Inline upvc handles have spindles that run through the middle of the handle and then into the window frame to operate the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have an unusual hook-shaped design. Cockspur handles are fitted with a single screw that holds the handle to the frame of the window and are not as secure as other kinds of window handles.

Handles that turn and tilt

The tilt and turn handles are different from other handles made of upvc in that they can be rotated for opening the window, and then tilted into the window to allow air circulation. In general, they have a 7mm spindle on the back of the handle and are available in left and right handed versions.

It is essential to know the spindle size when buying replacement glass for a window upvc handle. Not all are exactly the same size. Drop something in the middle of the hole to measure the length. This is the length of the spindle that will fit in your window.

What is a spindle?

uPVC window handles operate in a similar way to doors, by turning the handle to activate an opening inside the frame. The latch opens the window, so it can be shut and opened. The handles can become damaged, especially if often used or are exposed to harsh environments. This could mean that you have to replace your uPVC windows handles as they might not operate the window handle replacement correctly in the future.

There are many different kinds of uPVC handles available including Espag, Cockspur and Spaded handles. These handles are designed to fit in the uPVC frames in different ways, and each type of handle has a particular spindle that is used to lock the mechanism fitted into the window. This is why it is important to identify the kind of handle you have installed on your uPVC window so you can get the correct replacement.

The base of the handle will tell the type of uPVC it is. A snap-in covers should be over the screw that holds the base of the handle in position. When you remove this cover, you will be able observe the second screw that holds the handle base in place. After both screws are removed, you should be able remove the handle from the uPVC.

After taking off the uPVC handle, remove it from the locking mechanism. Take note of the length of the spindle. You'll need purchase a double glazing replacement window with the same length as the original handle and locking device.

The spindle wears down and becomes inoperable with the locking mechanism. This could be due to corrosion, damage from frequent use, or a loosening locking mechanism. If this occurs, it is required to replace the window handle as well as the locking mechanism to restore the full functionality to your uPVC windows.

How do I take off the handle that was previously attached?

Window handles are susceptible to being damaged or even broken over the course of time. It is essential to fix them as quickly as you can to ensure your security. It is simple to replace a worn or damaged handle. The job can be completed in under one minute without the need for any special tools.

To remove the handle, you first need to remove the screw at the base of the handle. Once the screw is removed, the handle will be pulled away. There is a second screw that is located at the bottom of the handle's base and it can be removed as well. After both screws are removed, the handle can be completely detached from the base section of the window.

After the handle has been removed, you can take the new handle and line up the fixing holes with the holes that are currently in the window frame. If there is a cap or sticker on the new handle, remove it if necessary and then screw the handle in the appropriate position. It is important to check that the handle works once it is put in place. Turn the handle and make sure that the lock mechanism is in place.

Espag handles come with spindles that extend from the handle and slot into the multipoint locking mechanism of the frame of the window. Cadenza windows come with a blade with cutouts which fit into the lock mechanism. Cockspur handles are long and hang over the frame that surrounds the window or the transom bar crossmember.

After you have put in the new handle, place the spindle inside the window lock and tighten it. When the handle is fixated and secured, replace the snap-in cover and the screw cap (if applicable). The handle is now ready to use by opening and closing the window several times to check that it works properly and securely.

How do I install the new handle?

It's not that difficult to change the handle on your uPVC windows. The process is very simple. You'll need an screwdriver and a bit of perseverance. The first thing to do is to ensure that the old handle is in the unlocked position and then take out any screws that are visible. you can replace them by screw caps if you need. After you have removed the handle, you'll need to take note of the length of the spindle that extends from the back. This is crucial as it will determine the kind of handle you'll need to purchase.

Espagnolette handles are the most common kind of handle that is used on uPVC windows. They feature a spindle that is inserted into the handle and operates a locking mechanism inside the window frame. The handle releases the latch, allowing the window to open. During regular use and over time, handles for espagnolette may become damaged.

Cadenza handles are a second type of uPVC window handle that is commonly used on tilt and turn windows. They feature a protruding knife that works with a multiple-point locking mechanism within the window. They are more secure than espagnolette handles because they are able to open from the inside. You can replace them using the same method as you would do for handles made of espagnolette however, make sure that the new handle is angled, not flat.

Once you have determined the right handle for you then you can line up the new handle to the existing screw holes and then screw it into place. You should then put the screws back on and test that your new handle is operating properly. This is accomplished by moving the handle from the locked position to the unlocked and vice versa several times. It is possible to contact an expert to determine if you can resolve any problems. They can offer advice on how to solve the problem in a timely and effective manner.