Replacing uPVC Window Handles

Changing upvc window handles is a fairly straightforward job. The important thing is to ensure that the replacement handle fits the spindle cut out in the window mechanism.

If the steps below are followed properly If you follow the steps correctly, any cockspur handle can fit most windows. The most important factor is the step size of the handle.

What to Look For

A large portion of windows in the UK are fitted with uPVC handles, and over time they may begin to show signs of wear and tear. When this occurs, the handle may become loose or difficult to operate, making it necessary to replace it. This is a relatively easy task that can be accomplished by anyone who is comfortable with basic hand tools.

The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to locate the fixing pins or screws that hold the handle in position. These are usually located on the inside of the handle. They can be removed with a screwdriver and pliers.

When the handle is loose and sagging, gently pull it back from its hinges. It is then time to find a replacement handle that is the same design and size. This can be done on the internet or in a local DIY store, and the process should only take around five minutes using an screwdriver.

When replacing the handle of a uPVC handle, it is important to think about the step height. This is the distance between the handle's base and where it is placed within the frame of the window. This is a common measurement and you should confirm the height of the step prior to ordering an replacement handle.

There are a variety of sizes based on the kind of handle. Inline handles for uPVC windows generally feature lug centers of 31mm, and there are also cockspur handle types that have 43mm centres. Tilt-and-turn handles are commonly found on uPVC windows. They have a special design which allows the window be slid down to let in air and then turned to fully open the window.

The most common cause of breakage in uPVC handles is that they crack inside rather than breaking off from the base section. This can make them hard to open and is why it is essential to ensure that any replacement handle you buy has the same spindle length that your current one.

Remove the Old Handle

A poorly fitted or damaged window handles may cause your double glazed window handles-glazed windows to open or close incorrectly, and can result in them becoming stuck. This could be due to many reasons, including general wear and tear on the metal handle or corrosion. In these instances, it is vital to replace the upvc window handle as promptly as you can to avoid further damage or loss of functionality.

When replacing upvc windows handles, you should remove the handles that were previously installed from the window. To do this, begin by removing the screw that is encased when the handle is in the closed position. Once you have removed that screw, you can take off the handle. You can make the process easier by using an electric screwdriver.

It is also worth noting that the handles' screws could be hidden behind caps made of plastic, so it is recommended to use the Stanley knife to the screw caps and then remove them. After the old handle has been removed, you should then take a look at the square cut on the base of the handle to ensure that the new window lock handles will work with it. It is essential to measure the length of the spindle on the old handle and compare it to the dimensions of the window mechanism spindle cutout.

The various types of upvc window handles are: Espag handles, which are equipped with a central screw and can turn left or right; Cranked handles, that have two screws and are used on tilt and turn windows made of upvc; and Spade handles, with an arm with a flat surface and can be placed on either side of the window. Once you have a suitable replacement, it's just a matter of screwing the handle in place and ensuring that the spindle is correctly inserted into the lock mechanism. After you have done this then tighten the handle to the window frame. Your replacement upvc handles will now be secure.

Take a look at the Spindle

If you need to replace a upvc handle that has fallen, it's likely the spindle holding it in place is damaged or is loose. In some cases this can be fixed by using a screw or pin to secure it. In other instances, it may have to be replaced completely. There are several kinds of window handles made of upvc. These include inline espagnolette handles as well as cockspur handles. tilt and turn window handles and turn handles. Each type of handle is installed and replaced in a different fashion.

Before purchasing a replacement handle it's important to know the dimensions of the handle that is currently in use. This will ensure that the new handle is the right size and will fit correctly within the window. Fortunately, all handles adhere to industry standards for sizing, so it's relatively easy to identify the right size.

To measure the handle's size move the window to the open position. Then, you should be able see the size of the screw or pin that is holding it. Then, use a tape measure or ruler to determine the length of the spindle. Once you have determined the length of the spindle you can purchase a new one that is exactly the same size.

When you are looking to replace a handle window handle, it is crucial to consider the step height of the window handle made of upvc. The step height is measured from the base to the point at which the handle is placed on the frame. Typically, this is about 21mm for uPVC windows or 9mm for aluminum. To be sure that the new handle will fit, you can drop something into the gap to check the distance it will go before meeting an obstruction.

Cockspur handles come with different backsets depending on what type of window you put them in. Inline Espag handles have an average height of 43mm from centre to centre (2 fixing points). Cockspur handles, however have different backset heights according to the shape of the window they're in. This is because they feature a spur that extends from the handle and locks over a cockspur wedge striker.

Install the New Handle

After you've chosen the new handle, make sure it is aligned with the holes for screws on the conservatory door handles. Then secure it using the screws provided. Install the latch lever in similar fashion to the handle on the main handle in the event that you are replacing the patio door handle locks handle. Then, you can attach the patio door handle trim once more to hide the screws for mounting.

Tip: To remove a metal head from a wedge made of wood, place the handle on the floor, so that its wide end is on the ground. Then use a hammer and tap the thin end. Be careful not to scratch the handle or the spindle.