Replacing uPVC Window Handles

The replacement of window handles made of upvc is a fairly straightforward task. It is crucial to make sure that the new handle fits into the spindle cutout of the window mechanism.

If you follow the steps below any cockspur handle can fit most windows. The step height of the handle is crucial.

What to Find

Over time, uPVC handles on many windows in the UK can start to show signs of wear and tear. The handle on the window can become loose or difficult-to-operate when this happens. Anyone who is comfortable using a basic hand tool is able to complete this job.

The first thing to do is make sure that the handle is firmly fixed to the window frame, and is in a position that is open. Next, locate the pins or screws which hold the handle. These are typically located on the inside face of the handle and are removed using a screwdriver or pliers.

Once the handle has become loose, it can be removed from its hinges by gently pulling it off. Then, you'll have to locate a new handle in the same size and style. This can be accomplished online or at a local DIY store, and should take about five minutes with an screwdriver.

One important factor to consider when replacing a uPVC window handle is the step height. This is the distance from the base of the handle to where it rests on the frame of the window. This is a common measurement and you should confirm the step height before ordering the replacement handle.

Depending on the kind of handle you choose, there are different sizes available. Inline handles for uPVC windows usually feature lug centers of 31mm, and there are also handles with cockspur that have 43mm centres. Tilt-and-turn handles are common on uPVC Windows. They have a special design that lets the window be tilted for ventilation and then turned to fully open the window.

The most common cause of breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This makes them difficult to open and therefore it is crucial to ensure that any replacement handle you purchase has the same length of spindle as the one you have.

Remove the old Handle

If your window handles are damaged or not properly installed, they could cause double glazed door handles-glazed windows to not open or close correctly. They could even become stuck. There are a myriad of reasons including general wear and tear, or corrosion of the metal handle. In these situations it is essential to seek replacement upvc window handles immediately in order to prevent further damage and loss of function.

When replacing upvc windows handles, you should remove the handles that were previously installed from the window. Start by removing the screw covered when the handle in closed position. This will reveal a screw, and once it is removed, you can then begin to take off the handle itself. It is recommended to use an electric screwdriver for this, as it makes the job easier and faster.

It is also important to be aware that screws could be hidden in plastic caps. It is recommended to remove the covers with a Stanley knife. After you have removed the old upvc window handles handle, you'll be required to inspect the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. This is important because you'll need to measure the length of the spindle on the previous handle to ensure that it is in line with the size of the window mechanism and the handle spindle cut out.

The various types of window handles made from upvc include: Espag handles, which feature a central screw that can turn left or right; Cranked handles that have two screws and are used on tilt and turn upvc windows and Spade handles that have an arm that is flat and can be placed on either side of the window. Once you have found a suitable replacement, it is simple to screw the handle into position and making sure that the spindle is correctly placed into the lock mechanism. After that the handle should be secured to the window frame and the replacement window handles made of upvc should be secure.

Measure the Spindle

If you're looking to replace a upvc handle that has collapsed, it's likely the spindle holding it in place is damaged or loose. In some cases you can tighten the spindle by using pin or screw. In some instances it is necessary to replace the handle. There are a few different types of upvc window handles. They include espagnolette handles that are inline, cockspur handles, and tilt and turn handles. Each handle type has its own procedure for installing and removing the handle.

It is essential to measure the handle prior to purchasing a replacement. This will ensure that the new handle is the correct size and will fit correctly into the window. All handles are calibrated according to industry standards, making it easy to identify the correct size.

To determine the size of the handle, turn the window to the open position. You should be able see the dimensions of the pin or screw that holds the handle. Use a ruler or a tape measure to determine the length the spindle is. Once you have determined the length of the spindle you can purchase a replacement spindle that is exactly the same size.

When buying a replacement you should consider the step height of the window handle made of upvc. The step height is measured from the base to the point where the handle for patio Door sits on the frame. It is typically approximately 21mm or 9mm in aluminium and uPVC. Dropping something into the space will allow you to determine how far the handle extends before it comes into contact with an obstruction.

Cockspur handles come with different backsets based on the type of window you put them in. Inline Espag handles have an average height of 43mm from centre to centre (2 fixing points). Cockspur handles, however have different backset heights dependent on the design of the window they're in. This is due to the fact that they have a spur which extends from the handle and locks onto a cockspur wedge-striking plate.

Install the new handle

Once you've selected the new handle, make sure it is aligned with the holes for screws on the door. Secure it using the screws provided. Install the latch lever the same manner as the handle that you are replacing in the event that you are replacing the door handle. After that, attach the door trim again to hide the screws for mounting.

Tip: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is on the floor. Then use an hammer and tap the narrow end. Be careful not damage the handle or the spindle.